素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-

pic14 - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts- OpenFlexure Microscope

素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-

前回からかなり機関が開いてしまいましたが、次はPrinting partsです。3Dプリンタで作る部品のことでしょうね。

サイト翻訳

Printing the plastic parts

パーツを印刷するか誰かからもらってくれと。

PLAフィラメントでRepRapスタイルのプリンタならほぼ確実に印刷できる。作る顕微鏡のタイプによって必要なパーツが違ってくるので、作り方を読んでから印刷するか、Configure and Download STLsのページから、ダウンロードするのがよいでしょう。

今使っているプリンターは、Crearity Ender3 SIとAnycubic MEGA-S。これって、RepRapスタイルなの?

よくわかりませんが、大丈夫じゃね?

普段PLA使わないからなぁ...。そういえば、PLAの木質フィラメント余ってたっけ。木の顕微鏡ってのも面白そう。

Standard builds of the microscope

標準バージョンを作りたい人は、Webcam-based microscope または、High resolution microscope の部分だけでOK。カスタマイズしたい人はページ下部のところまで印刷。

High resolution microscope で電動化するつもりなので、Webcam-based microscope の部分はスルーします。

Webcam-based microscope

省略

High resolution microscope

医学や科学的研究に使われる対物レンズが必要。光学系パーツとサンプルマウントがほかのバージョンとは違うところ。

おぉ~、本格的な感じに仕上がりそうですね。

本家サイトのSTLファイルへのリンクを張っておきます。

Plastic tools
actuator_assembly_tools.stl バンドおよびナット挿入ツール、バンドツールホルダー
https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Factuator assembly tools - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/actuator_assembly_tools.stl
lens_tool.stl 直径13mmコンデンサーレンズ挿入ツール
https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Flens tool - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/lens_tool.stl
picamera_2_lens_gripper.stl PIカメラレンズ取り外しツール(付属していなかった場合のみ必要)
https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Fpicamera 2 lens gripper - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/picamera_2_lens_gripper.stl
Components
main_body_LS65-M-BS.stl / main_body_LS65-M-BS_brim.stl 顕微鏡本体
https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Fmain body LS65 M - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/main_body_LS65-M.stl

↑ビルドプレートへの定着に自信のある人用

https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Fmain body LS65 M BS brim - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/main_body_LS65-M-BS_brim.stl

↑ビルドプレートへの定着に自信のない人用(ブリムが最初から含まれています)

feet.stl / feet_tall.stl 本体の脚
https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Ffeet - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/feet.stl

↑無限遠補正光学モジュール(?)なるものを使ってなければこれでいいそうです。

https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Ffeet tall - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/feet_tall.stl

↑無限遠補正光学モジュールを使っている場合はこれなんですかね。普通に作るならこれじゃない方でいいんだと思います。

gears.stl 歯車
https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Fgears - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/gears.stl
illumination illumination_dovetail.stl 照明垂直接続部品
https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Fillumination dovetail - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/illumination_dovetail.stl
illumination condenser.stl コンデンサーアーム
https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Fcondenser - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/condenser.s
sample_clips.stl サンプルクリップ
https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Fsample clips - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/sample_clips.stl
optics_picamera_2_rms_f50d13.stl / optics_picamera_2_rms_f50d13_beamsplitter.stl 光学モジュール

黒で印刷!

https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Foptics picamera 2 rms f50d13 - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/optics_picamera_2_rms_f50d13.stl

↑transmission illumination用

https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Foptics picamera 2 rms infinity f50d13 beamsplitter - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/optics_picamera_2_rms_infinity_f50d13_beamsplitter.stl

↑reflection illumination用

microscope_stand-30.stl / microscope_stand-30-BS.stl 顕微鏡スタンド
https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Fmicroscope stand 30 - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/microscope_stand_30.stl

↑普通のヤツ

https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Fmicroscope stand 30 BS - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/microscope_stand_30-BS.stl

↑reflection illuminationにする場合

sample_riser_LS10.stl サンプルライザー
https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Fsample riser LS10 - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/sample_riser_LS10.stl
For motorised operation you will also need

電動化する場合必要

small_gears.stl 小歯車
https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Fsmall gears - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/small_gears.stl
motor_driver_case.stl モータードライバーケース
https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Fmotor driver case - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/motor_driver_case.stl
For reflection illumination you will also need

reflection illuminationにする場合

・・・しないので省略

Additionally, you will need

追加

RMSのねじ切りしてある有限系対物レンズ。肩からサンプルまでの距離が45㎜の場合はライザーが必要。35㎜の場合は不必要。

直径12.7mm、焦点距離50mmのアクロマティックレンズ。 ThorLabsac127-050-aまたは同等の一般的なもの。

コンデンサーレンズ用直径13mm、焦点距離5mmのPMMA平面凸レンズ。(LEDレンズとしてまとめて販売されている)

モーターとモータードライバー関係の電子部品。

Print settings

プリント設定。プリント前に読むべし。

Prusa i3 Mk3 か Ultimaker2 でPLAフィラメントを0.2mmレイヤーで印刷すると、本体(main_body〇〇〇.stl)を印刷するのに10時間ほど。

標準は0.2mmレイヤーってことですね。

で、注意書きには、サポート材なしで印刷できるように設計してあるとのこと。親切~

スライサーのBrim設定は使わない。ビルドプレートへの定着に問題ある場合は、Smart Brimを使う。

↓これです。

pic15 1024x768 - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-

サポートが必要な部品はないけど、ブリッジが必要な部分はあるらしい。

ブリッジが上手く印刷できるかどうか確かめるために、just_leg_test.stlを印刷してみるとよい。うまくできなかった場合はスライサーを調整のこと。

初期設定ではブリッジ印刷がOFFになっているスライサーもあります。

just_leg_test.stlが上手く印刷できないからとサポートをONにすると、こ・わ・れ・るらしいです。

just_leg_test.stlはこれ↓

https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Fjust leg test - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/just_leg_test.stl

3Dプリンターのビルドプレートが180mm×180mm以上あれば、パーツを並べといて一気に印刷できる。

でも、一個ずつ印刷した方が無難だよなぁ。

印刷設定の適・不適を見るには、just_leg_test.stlを印刷してみる。

といいらしい。

光学モジュールは他のパーツを一緒に印刷すると、各層の所要時間が長くなり、フィラメントが固化する余裕ができる。

のでお勧めらしい。まあ、スライサーの設定で何とかしましょう。

光学モジュールは、チューブ内の迷光を減らすために黒で印刷するのが最適。

他の色でも大丈夫だって書いてはあるけどね。

Smart Brim

main_body〇〇〇.stlでスライサーのBrimを使うと必要な隙間を埋めてしまう場合がある。それ以外は使っても大丈夫。

だけど、smart brimの方がいろいろいいらしい(激略)

スライサー設定としては、cura v4.4は特に問題なし、PrusaSlicer v2.1.1 はデフォルト設定で問題なしらしい。現行バージョンより古いけど、まぁ、大丈夫でしょ。

結論。Smart Brim選択しといてスライサーのBrimはOFFの一択です。

Clean-up of printed parts

パーツを印刷したら顕微鏡本体の3つの穴をドリルで開けること。

M3のネジが通る部分なので、3mmのドリルですかね。ボルトの通りをよくするためだと思います。

ペンチを使用して、サンプルステージの下側からプラスチックの緩んだ紐を取り除きます。

スマートブリムの残骸かな?

アクチュエータカラムケーシングと真ちゅう製ナットを保持する中央アクチュエータカラムの間にも関係があります。
これらは、後の手順で説明するように、スナップする必要があります。
また、2つの細い脚のペアと、顕微鏡の周りを走る「壁」との間に短い結びつきがある場合もあります。
これらもナイフでスナップする必要があります。
脚の各ペアの間の「はしご」のような構造も、印刷中のサポートのためだけにあります。
そのままにしておいても害はありませんが、「ラング」を切り取ると、ステージがもう少し動くようになります。

え~、よくわからなかったので、直訳のまま載せておきます。多分、組み立てる段階でわかるようになると思いますので。

印刷部品を入手したら、アクチュエータを組み立てることから始めましょう。

はい。

Extra details for custom microscopes

上記の2つの標準ビルドのいずれかをビルドする場合は、このセクションを無視しても問題ありません。

パーツごとの詳細が書かれていますが、自分なりにカスタマイズする時に必要になるのでしょう。今回は特に必要なし。

でも、一つだけ...

VitonOリングを手に入れることができない場合、代替手段の一つとして、柔らかいTPUフィラメントを使用していくつかのOリングを印刷することです。

おぉ~。そうなんです。バイトンオーリング、なかなかちょうどいいサイズが見つからないのです。

これ用のSTLファイルは

https%3A%2F%2Fbuild.openflexure.org%2Fopenflexure microscope%2Fv6.1.5%2Factuator tension band - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-
https://build.openflexure.org/openflexure-microscope/v6.1.5/actuator_tension_band.stl

これだそうです。

よく見るとこんなところにチェックボックスがあった!

pic16 1024x768 - 素人が3Dプリンターで顕微鏡を作る⑥ -Printing parts-

▼Advancedをクリックすると出てきます。これにチャックを入れとけばまとめてダウンロードしてくれます。TPUで印刷ですので間違えないように。

おわりに

今回もかなーりのいい加減訳になりましたが、多分必要な部分は翻訳出来ていると思います。

不安な人は本家サイトと見比べながら進めてください。

タイトルとURLをコピーしました